Working order - Dent at the back but does not effect use - No holes, some surface rust

Spares or repair - 2,200 gallon capacity - Nearly new 23.1-26 tyres that are both holding air, needs new bearing seals - C/w PTO shaft - Lights and brakes not working

Done minimal work since having new bearings and new 150hp impeller

Was running when last used but needs a new battery and throttle cable - Minimal use since buying new

Serial No: 15206 - Has disc coulters - No manual vari-width - NO hydraulic vari-width - No previous welds or repairs - One mouldboard cracked, another well worn - Disc spins but seized so will not twist side to side

Has some welds on mouldboards, one cracked - One disc coulter missing

Manual boom fold - 12m width - Hydraulic lift - self levelling - Induction/wash tank - 1000L capacity - Lights untested - Electric control box - PTO guard intact - Usable condition

240v - Working order when last used - Flat belt - Has been used to fill log trailer - Approx 8' elevation - Spare belt included

Single furrow turnover plough - Been used as garden ornament

C/W rear gates and PTO shaft (needs new guard) - Would need approx 10 new tines - Some perishing to tyres

Tyres holding air, some perishing - PTO guard intact - All tines present - Both gates present - Working order

Working order - Would benefit with replacement brushes

C/W PTO shaft - Good working order - Adjustable height

Working order - C/W electric motor - 13AMP - 2 flat tyres

Approx 6' long x 18'' round - iron can be removed if not wanted

Approx 5' 6'' long x 18'' round

Spares or repairs - Tank capacity 800 litre - 12' working width - Loading available - Lorry access up to 8 wheels

Spares or Repairs

Mostly complete - Some rust and hole in one mouldboard - Marked: Ransomes Sims & Jefferies

Was working last year - C/w a full set of seed belts - 6 rows - Could do with some Tlc and a service so could make for a good project - Loading available

2.2m (7') wide - Twin rotor with PTO shaft - Has always been barn stored - Loading available

Good working order - Done little work for age - Genuine dispersal due to relinquishing farm tenancy.

Good working order - Genuine dispersal due to relinquishing farm tenancy.

55MM rubber blade

C/w Hydraulic shut off - Wagtail - Good working order - Only been used for broadcasting seeds and slug pellets. Found to be less efficient for field beans so current owner changing to a new machine Has been barn stored - There is a small bolt and metal strip bolted on to the shut-off discs as seen in the photo. This seals a slot where seeds could get through and found to work for present owner.

Solid, heavy Cambridge Roller - In working order - Approx 2m in width

Serial No: 12119 - All works as expected - Loading available

Serial No. 1350 - C/w PTO shaft - Barn stored - All complete - Was used around 10 years ago as a topper - Loading assistance available.

C/w PTO shaft - 1 complete, has not been used/moved for many years - 2nd one dismantled with most parts included - Large quantity of spare tines and instruction book.

Spares or repairs - Runs but could use new bearings and rollers.

Galvanised frame - As new - Excellent condition

Serial No: 106146 - 15000 bale count - C/w control box - Early 90s - Barn stored and not used for 10 years - Lever on wrapper not working

Serial number unknown - 3m working width - Owned for about 10 years and used for a horse arena , grooming and paddock maintenance - Selling as need a wider machine for larger fields - Manual folding with wheels - Tyres in good condition - All tines present - One tine is slightly bent - Loading available by appointments on evenings or weekends

10' working width - C/w PTO - One rotor has broken away from the frame - Was a strong topper but has suffered from corrosion of some body parts - All mechanicals worked this year - Loading available.

Spares or repairs - Not used for some time - Does not have hose or gun.

Plenty of rubber left.

Working - One bottom skid is damaged as pictured.

Year and make unknown - Chains not blades - Rough but works - Loading available

C/w PTO shaft - 6' working width - In good working order - Solid machine - Has been used recently - Needs replacement support strap - Loading available

Serial No: 2134 - In good working order - C/w PTO shaft - Disc spinner - Would benefit with a free up but does open and close - Always been stored inside

8' 3'' wide - Good brush - One recent new hydraulic pipe - 3pnt linkage mounted - Jockey wheels - Good condition - Working order

Spares or repairs - Tub very rotten - Ram looks okay - Has been welded on frame in a place or two

As new

Spares or Repairs - Rusty needs wheel replacing

Spares or repair - Made from powerpack parts

2 x 3 point linkage points - Works well - Surplus requirements

Points ok and works well - Surplus to requirements

Works well - Has hydraulic ram to move deck across - C/w PTO shaft in good condition - Hydraulic pipes need renewing

2004 Fella 270 mower with conditioner - Spares or repairs - Serial Number: 4701 - C/w PTO shaft - Grass conditioner - Cutting width of 2.7 metres - Loading available - Unit on bed faulty

Year unknown - Mounted linkage -

Kverneland 12'' plough - Manual vari-width - Year unknown - C/w disc coulters (1 needs attention)

Serial Number: 342229 - Working width of 1.4m - Loading available - In working order - Used to reseed a small patch of land and no longer required. - Good tines - C/w PTO shaft

3 point linkage - Has some surface rust - Loading available - C/w holder to hold post - Worked well when last used

Good working order - 3 point linkage - C/w PTO shaft - Cable control box - SN: 3618W - Loading available - Block end housings are broken on all 3 but other than that in good working condition

600l tank capacity - 10m booms - SNTS certificate, expiry 22 July 2028 - SN: P128 - Used this year - Only for sale as upgrade

Spares or repairs - Unknown if working as not used for a few years - Has been used for conservation area - Small wheel on front is missing - Oil pipes good - Tyres good - Bale width believed to be 70cm - Pick up width 85cm

3 point linkage mounted or on loader brackets - Loading available

Spares or repair - 3 point linkage - Is repairable but needs new rubbers, skids and doors - Worn rubbers and worn steel

Reversible - 3 point linkage or A frame mounted - Rubber in very good condition - Adjustable wing angle

Disc coulters - All moving parts good and moving freely - Last used 3 years ago and was put away oiled and greased - C/w some spares

Not used for a number of years so will need attention - Believed to be 12m boom - C/w PTO - Up to 1000 litre tank

Twin disc - Not used for many years - C/w homemade wooden hopper extension

6' cutting width - Solid tyre - PTO present - Used recently - Slight rusting to tub

Loading available - Lorry access up to 8 wheels

Model: 31 - Strong framework - C/w tube for piping.

Strong framework - No loading available UNTIL 20th October - No viewing available, phone calls welcome.

Spares or repair - Needs new bearings - Good discs except for two damaged - No loading available UNTIL 20th October - No viewing available, phone calls welcome.

Working order, however transport linkage needs attention/repair - C/w PTO shaft - 3 rotors - Solid tub - No loading available UNTIL 20th October - No viewing available, phone calls welcome.

Filled with water & bungs seized - Rear scraper bar - Solid framework - No loading available UNTIL 20th October - No viewing available, phone calls welcome.

Marked 4 - Solid framework - Believed all rings are ok - Can be loaded - Part of a triple set being sold separately - No loading available UNTIL 20th October - No viewing available, phone calls welcome.

No loading available UNTIL 20th October - No viewing available, phone calls welcome.

C/w PTO shaft - Offset - Solid skids - Solid tub - C/w top link - Topper 5

PTO complete - Working order - Hydraulic shut off - C/w rain cover and extension hopper - Barn stored

Believe to be 10T model

Heavy duty cone style/auger wood chipper - Complete with PTO shaft (would need a new PTO guard) - Folds up for transport or storage as per the photo - Slip clutch - Adjustable flap on spout and rotation of spout - Was used for clearing up hedge laying brash

Marked as 3 - Spares or repairs only - Linkage damaged - Limited loading assistance with small digger

Working order - Pin and cone, or Manitou brackets - Only sold due to using cow mats instead of sand - Has some corrosion

Hitch lose but just needs new bolt - Solid framework - All rings appear complete - 2.4m from outside of frame

Marked 6 - Solid framework - Believed all rings are ok - Can be loaded - Part of a triple set being sold separately - No loading available UNTIL 20th October - No viewing available, phone calls welcome.

Vendor has owned for 25 years - Working order just used occasionally for bouting up peat - Nice vintage equipment - To shape and rebuild soil ridges for crops - Row widths can be altered to match varying crop requirements

Approx 4m conveyor belt with motor - Worked when taken out - 3 phase

Has been used on peat processing plant - Suitable for soil - Has a rubber belt - Holds approx 6 cubic meters - In working order - C/W purpose made steps to hopper

Rubber belt - Approx 6 cubic meters - Been used for dosing peat in a peat works but would be suitable for also dosing soil - Does not have a motor

New hoses & ram on lid recently - C/w PTO shaft - Used this year - Solid tub - For sale due to owner upgrading

Working order - Last used 2 years ago to turn straw - Please note slip clutch does need attention, as if in heavy work it does struggle

In-line topper - No PTO shaft - Solid tub & skids

C/w PTO shaft - Tyres holding air, some tread - Works - Some decay/corrosion in places on tub - Viewing & enquires welcome

Works but has previously been welded

Owned from new, approx 10 years old - Working order - Barn stored - Tyres holding air - Jack legs - Hydraulics in working order - Used until recently - Crane will detach & fit on 3 point linkage

Bale trailer/Lorry conversion - 22' bed length - Lights present & working - 9t carrying capacity (capable of carrying 14 bales of silage) - Oil brakes & working - C/w front & rear lades - C/w strap tie downs - New floor fitted August 2026 - Tyres in average condition - C/w 2 spare wheels & a spare bale lade

New body built on - Good strong ram - Removable drop sides & tailgate

C/w front and back bale lades - Solid metal floor - Brakes and lights work - Used this summer - 12.5 - 15.3 tyres - Recently been painted

6' wide - C/w front and rear lades - Wooden floor (solid) - Tyres holding air - This lot is part of a genuine dispersal on behalf of a deceased estate and the farm is being sold. - Please note that much of the machinery equipment has not been used for many years and the farm has no capability of loading heavy or large lots.

Spares or Repairs - SN: 5895 - Lights present but untested - Air brakes are stuck on so believed to have a leak - C/w front lade - C/w strap tie downs - Wooden floor needs new boards & some metal cross members - Tyres hold air but tread is low - Trailer has a strong chassis

Thought to be 10 tonne capacity - Auto door (has some plating to anchor point) - Lights and hydraulic brakes present - untested - Tyres holding air - New seals in rams recently - Floor sound

Body Craft livestock box with a Merrick Login conversion trailer - S/N: 190310 - Box is 24' and trailer is 25' - Lights present and working - Brakes and handbrake working - C/W cattle partition gate - Tyres in good condition - Roof may need some attention - Has been used every few weeks, up until recently

12' x 6' - Lights and brakes not working - C/w front and rear lades - Weldmesh floor - Tyres are old but holding air