Very tidy - Tines all present - Has had another set of brackets welded on

No brackets welded on - 2 new pipes - Pin & bushes tight - Non removable sleeves - Can be loaded

Euro 8 brackets - Removable tubes for the bale spikes - One spike has slight bend, doesn't effect use

Good condition for age - Rams in good condition with no leaks - All working as it should be - Handy bit of kit - Loading available

Six months old - 7ft width - Euro 8 bracket - Done hardly any work - No faults at all - Selling as too big for tractor

Removed from International B250 - All complete - C/w bucket & tipping ram

Tractor mounted - Cat 1 pin size - 1.1m width - 200l hopper - This has never been used but is very shop soiled

Euro brackets - 1200mm length of forks - Very shop soiled

Little work

On euro brackets, BRU200 - 2.0m width - As new only used a handful of times

Was a shear grab - Several tines missing - Quicke 3 brackets

Two 2 foot spikes - Tines are loose

Solid spikes - Believed to be Faucheux brackets

Some small holes/rust flaking - Believed old style Faucheux/Quicke brackets

Very heavy (steel welded to bottom) - Solid

C/w manitou brackets - Outside tines have been taken off - Working order - Twin ram

Have been cut off with gas.

To fit Merlo - 7'9'' wide - Good strong bucket - Some cracking/splitting to bottom

Quicke No3 brackets - Some rust holes in base - Useable condition

On Manitou brackets - Strong bucket, some wear on cutting edge and a few holes in bottom - Galvanised sutton brush - Has had a repair on arm - Brush good

Manitou brackets - 1780 litre capacity - Blade in good order - Little use - No holes - Only used for grain

Pin & Cone brackets - Approx 5 tines damaged - Pipes present - Some damage to mesh - Vendor has the rams but not fitted

Hard PX tines - Good working order - Some rust on rams - Chilton brackets - Done little work for age - Genuine dispersal due to relinquishing farm tenancy.

Good working order - Chilton brackets - Genuine dispersal due to relinquishing farm tenancy.

Manitou brackets - Good working order

Euro brackets - Good working condition - Used a handful of times

With manual trip tip - Selling as no longer needed - In overall good condition - Some surface rust/blistering on base but still sound

Euro bracket - Four tine bale spike

Spares or repair - Euro 8 brackets - Age and brand unknown - Needs attention/welding but repairable - All tines present - No rams or hoses

In working order - Used until recently - 7' wide - Tines all present and straight - Sanderson brackets - Selling due to upgrade

Bobcat bracket - Good condition

Euro brackets - As new condition only been used for light use previously

60mm pins

Euro 8 brackets - Top bar needs welding.

Pin and cone bracket - Useful attachment

Fits on front loader spikes - Carrier is approx 173cm x 126cm

Fitted with MX brackets - Good condition - Selling due to retirement

Good condition

Hydraulic tipping - 3 point linkage - Little use

1m long - Adjustable width - No damage/cracks.

Including rams and a spare spike - Previously fitted to a David Brown

No forks

Removable tubes for use of spikes - Manitou or Euro brackets - Top hoop come with - No pipes

On quick fit bracket

12'' toothed bucket - 28mm pins - Used on a micro excavator

EURO 8 WELD ON LOADER BRACKET

For John Deere

Good condition - 2 cubic meter front bucket

Good condition

5 weights - Marked 276-43R - Thought to fit John Deere 4020

2 wheel weights - Thought to fit John Deere 4020 - Marked A3404R

Approx 80kg each - Unknown what removed from

3 point linkage

Spares or Repairs - Oil drum filled with concrete - 3 point linkage - Would benefit from a new bar

On Euro 8 bracket and A frame - Good and strong - 2' x 2' concrete block

3 point linkage (damaged) - Concrete is approx 110cm wide x 40cm thick and 85cm high - This lot is part of a genuine dispersal on behalf of a deceased estate and the farm is being sold. - Please note that much of the machinery equipment has not been used for many years and the farm has no capability of loading heavy or large lots.

50kg each

50kg each

50kg each

Would suit small tractor

Parlour to include all stall work, feed troughs, gates, receiving vessel, milk pump, ADF, Dematron Milk Meters, Auto ID, Feed to Yield Computer, ATL Feeders, Compressor & Vacuum Pump - All in good working order up to the 19th August 2026 - Already dismantled & boxed ready for a new home - Stopped using this year due to robot installation

5-6 years old - Includes wall brackets - Good condition - Removed due to robot installation

No Lid - Painted - Some Knock Marks

Painted - Some Knock Marks

Painted - Some Knock Marks - Marked C.W.S LTD on lid

Approx 40 foam mats - 5 rubber filled mats - 2 rolls of rubber covers

400,000L capacity - New and unused - Still packaged - 13.3M x 22.7M equipted with 8 x 4inch brass valves - 2 on either side

C/w submersible pump

4 digit - C/w straps and clips - Working

4 digit - C/w straps and clips - Working

4 digit - C/w straps and clips (some may need attention) - Working

4 digit - C/w straps and clips (some may need attention) - Working

Serial number: 00007884 - Previously used in milk processing set up to hold milk before pumping into seperator

To read AFI Milk Pedometers - 2 readers & one activity adaptor box - Were all working when removed from the parlour.

69 AFI milk activity monitors - 56 old style - 13 new style - Were all working when removed from the cows - C/w plastic clips for leg straps.

Spares or repairs - Control box

Spare parts and control boxes and spare pipes

Single phase - Unsure of output - Working when removed

C/w 2 x 200L churns - Coin, card and note readers - Purchased new in 2018 - All working as it should

Spares or repair - Washes 12L bottles well and quickly - 2 different wash cycles - Self dosing detergent and rinse aid - Integrated water heating - Needs a new pump (about £250 according to sales rep) - Good simple machine - C/w 2 wash trays and any left over rinse aid - £1000 new to buy

20 aside - Rapid exit parlour - Approximately 20 years old - C/w all pipe work to bulk tank area - No tank, plate coolers or compressor included - All electric boxes included - Steelwork and gates included - Manual backing gate - Air exit gates - Feeders are available if required but they are not fitted (Daltec system) - Buyer to dismantle & remove - Last used in November 2025 - Viewing recommended.

Bought as working 4 years ago but never used so unknown working condition

Stainless steel - Removed from dairy after retirement - 20 plus years old - Good working order prior to removal, was very efficient at cooling milk quickly - Wall mounted, could also be used in the brewing industry

Marked as 1 - 5' 4'' diameter x 3' high - C/w pins - Good condition - broken rail has been repaired

Marked as 2 - 5'4''' diameter x 3' high - C/w pins - Good condition

Galvanised - Good condition - Little use

Vintage - C/w original clipper head - Additional clipper head - Cast iron frame on wooden stand with toolbox - Very original - Working order - C/w spare blades

Approx 7'6'' diameter x 26'' skirt - Needs a little work - Two tombstones missing

Galvanised steel - 21'' deep x 2' square

Sheeted sides - Mesh fronts - 4' long X 2' wide X 1' deep

One side cracked

Cracked.

ROUND SHEEP FEEDER

ROUND SHEEP FEEDER

ROUND SHEEP FEEDER