1.5hp single phase motor and starter - Working when last used but not been used for several years

As new - 8ft cut - Cut less than 100 acres by a retiring farmer

New PTO guard recently - Spare tips & star joints - 12'' auger - Spare auger included

Tines all present - Tyres holding air - PTO intact - Usable condition

8' roller and frame - Good rings

6'' rollers - C/w PTO shaft and guard - Working order

For quad or compact tractor - Disc - Been dry stored - Control linkage will need freeing off - Will need minor recommissioning as it has been in dry stored for some time - Sold as seen

SN: 202000612017 - Loading available - 1.35m working width - Has only done approx 3-4 hours work from new

Water filled (currently empty) - Recent new wooden bearings - In frame (8 1/2' wide total) - Only being sold as vendor has bought a lead and following roller - Used this year

Not used for 2 years - Working order - No stand or rear gates - C/w PTO

Been stored indoors - Comes with PTO shaft and control box

Solid frame. - On ring hitch.

Cast bench - PTO driven belt drive

All good bearings - New chains about 20 loads ago - All working

Hydraulic - Used recently - Working order but does have slight oil leak on spool valve - 3 point linkage

C/w transport trailer - Bought by current vendor 2 years ago but they have never used it, so working condition unknown

11 legs - Tines all good - Shear bolt gone in one leg - Good and strong - Can be loaded

Fitted with 24m spread discs - OM 18-24 discs - Boarder control kit - Lights present

Some weld repairs on linkage framework - Working order - C/w PTO shaft - Hydraulic folding - Solid tub

Working order - Dent at the back but does not effect use - No holes, some surface rust

Has some welds on mouldboards, one cracked - One disc coulter missing

C/W rear gates and PTO shaft (needs new guard) - Would need approx 10 new tines - Some perishing to tyres

Tyres holding air, some perishing - PTO guard intact - All tines present - Both gates present - Working order

Working order - Would benefit with replacement brushes

C/W PTO shaft - Good working order - Adjustable height

Working order - C/W electric motor - 13AMP - 2 flat tyres

Approx 6' long x 18'' round - iron can be removed if not wanted

Approx 5' 6'' long x 18'' round

Spares or Repairs

Mostly complete - Some rust and hole in one mouldboard - Marked: Ransomes Sims & Jefferies

Solid, heavy Cambridge Roller - In working order - Approx 2m in width

Serial No. 1350 - C/w PTO shaft - Barn stored - All complete - Was used around 10 years ago as a topper - Loading assistance available.

C/w PTO shaft - 1 complete, has not been used/moved for many years - 2nd one dismantled with most parts included - Large quantity of spare tines and instruction book.

Galvanised frame - As new - Excellent condition

Spares or repairs - 10' working width - C/w PTO - One rotor has broken away from the frame - Was a strong topper but has suffered from corrosion of some body parts - All mechanicals worked this year - Loading available.

Spares or repairs - Not used for some time - Does not have hose or gun.

Working - One bottom skid is damaged as pictured.

C/w PTO shaft - 6' working width - In good working order - Solid machine - Has been used recently - Needs replacement support strap - Loading available

8' 3'' wide - Good brush - One recent new hydraulic pipe - 3pnt linkage mounted - Jockey wheels - Good condition - Working order

2 x 3 point linkage points - Works well - Surplus requirements

Works well - Has hydraulic ram to move deck across - C/w PTO shaft in good condition - Hydraulic pipes need renewing

Year unknown - Mounted linkage -

Good working order - 3 point linkage - C/w PTO shaft - Cable control box - SN: 3618W - Loading available - Block end housings are broken on all 3 but other than that in good working condition

Spares or repair - 3 point linkage - Is repairable but needs new rubbers, skids and doors - Worn rubbers and worn steel

Reversible - 3 point linkage or A frame mounted - Rubber in very good condition - Adjustable wing angle

Disc coulters - All moving parts good and moving freely - Last used 3 years ago and was put away oiled and greased - C/w some spares

Not used for a number of years so will need attention - Believed to be 12m boom - C/w PTO - Up to 1000 litre tank

Twin disc - Not used for many years - C/w homemade wooden hopper extension

Loading available - Lorry access up to 8 wheels

Model: 31 - Strong framework - C/w tube for piping.

Working order, however transport linkage needs attention/repair - C/w PTO shaft - 3 rotors - Solid tub - No loading available UNTIL 20th October - Phone calls welcome and viewing by appointment

PTO complete - Working order - Hydraulic shut off - C/w rain cover and extension hopper - Barn stored

Hitch lose but just needs new bolt - Solid framework - All rings appear complete - 2.4m from outside of frame

Vendor has owned for 25 years - Working order just used occasionally for bouting up peat - Nice vintage equipment - To shape and rebuild soil ridges for crops - Row widths can be altered to match varying crop requirements

Approx 4m conveyor belt with motor - Worked when taken out - 3 phase

Has been used on peat processing plant - Suitable for soil - Has a rubber belt - Holds approx 6 cubic meters - In working order - C/W purpose made steps to hopper

Rubber belt - Approx 6 cubic meters - Been used for dosing peat in a peat works but would be suitable for also dosing soil - Does not have a motor

Works but has previously been welded

Solid trough, no holes - Legs strong - Galvanised.

Not used for 2 years - Working order - No stand or rear gates - C/w PTO

Not used for 2 years - Working order - No stand or rear gates - C/w PTO