Marked 10 - Sandstorm sander - KR 600RE drill (working order) - Clamp lead light not working - Due to limited availability of the vendor we will hold a collection morning on Tuesday 20th October between 9.00am and 12.30pm There will be no alternative collections under any circumstances

Marked 17 - Both aluminium - 3' x 6' - 6'' one has damage to bubble - Due to limited availability of the vendor we will hold a collection morning on Tuesday 20th October between 9.00am and 12.30pm There will be no alternative collections under any circumstances

Marked 25 - 240 volt - Working order - Only one grinding wheel - Due to limited availability of the vendor we will hold a collection morning on Tuesday 20th October between 9.00am and 12.30pm There will be no alternative collections under any circumstances

Very heavy - Very strong

3 saws - Various sizes

C/w 5 additional bits - C/w clamps & small wooden worktop stand - In good order - 240v - C/w manual - Purchaser will need to either bring people power to lift out of position or co-ordinate with owners if assistance is needed

Length in photos - All complete

Lengths in photos - All complete

Spares or repairs - Cable needs attention - But in working order when last used

Both sections 10' long.

A couple of rungs are missing - Slight bend.

C/w key - Has been used as a medicine cabinet - 28'' high X 18'' wide X 25'' deep - Some rust patches

11O volt - Working order - 305mm diameter disc

New and unused - 15w

Working when removed from system (replacement biomass boiler had it's own inbuilt vacuum system) - Length of auger with single phase motor

Used for crimping ribbon cable fittings but could be adapted for other applications

10 leads - Various lengths from 1m-6m - 4 to 6 gang trailing sockets

Pack of 10 x 800mm lengths - Length 12-30V DC - Silicon embedded - Can be used for vehicle lights or general lighting

Pack of 10 x 800mm lengths - Length 12-30V DC - Silicon embedded - Can be used for vehicle lights or general lighting

Pack of 10 x 800mm lengths - Length 12-30V DC - Silicon embedded - Can be used for vehicle lights or general lighting

Pack of 10 x 800mm lengths - Length 12-30V DC - Silicon embedded - Can be used for vehicle lights or general lighting

Pack of 10 x 800mm lengths - Length 12-30V DC - Silicon embedded - Can be used for vehicle lights or general lighting

Pack of 10 x 800mm lengths - Length 12-30V DC - Silicon embedded - Can be used for vehicle lights or general lighting

Will take 2 full size gas cylinders - Has pneumatic tyres

55cm wide x 98cm long x 52cm high - Made from 50mm x 100mm box section steel with aluminium tread plate panels to three sides

Working order - Video shows generator working

Good working order - 240v - Diamond tipped blade

Untested

Approx 5' 10'' tall - slight bend to the bar

Approx 26'' long

Not working but not sure why

9 x 9 x 24 inc lockable box - New

New & unused

300kg rating - Good condition

New & unused

Used condition - Marked: Redashe - Useable condition

Recently removed from a flat roof - 1200mm x 1200mm - Aluminium frames

Unused - Original case with 8 sockets

Working order when removed

Working when removed from workshop - Wiring will need attention - Cast bench/table

240 volt - Working condition.

3 x v-belt model - PTO shaft intact - Working order - Blade good, recently sharpened

No motor

Various tools including box of large drill bits - Makita saw (in case) - Pipe bender - Electric cables

C/w stand - Excellent condition - Light use - Many extras (too many to list)

15''-24'' long

8 Marples professional wood turning chisels - 15'' long

Special addition

As new

Many dividers included

C/w rivets

Little used

Good piece of kit

C/w blade and in working condition

Spares or repairs - Not running, hence sale as spares and repairs.

Spares or repair - Missing handle

Works as expected

Works as expected

Used for holding welding gas bottles

Electric motor - Well used but still runs - 1 wheel is seized.

In working order.

Single phase 240v - In working order - With surface planer, mortiser attachment, spindle moulder with 6 sets of cutters, a selection of circular saw blades, belt sander attachment and a grinder attachment

All with brass tops - 2 BP cans in fairly good condition - 1 Esso can has a few dents and a solder repair on it

Antique hand chisel mortiser, with a variety of chisels - Loading available.

Cast iron - Used in vehicle restoration - Working order

Approx 3'5'' from end of each eye

Has been used in vehicle restoration for edging sheet metal - Made by a company called Edwards

Approx 20

Approx 20

In plastic case

5' long - Hydraulic jack

6.0KW - Electric start - 411 hours - New battery fitted - Fitted with wheels.

MAGNETIC LED LIGHTS

3T capacity

Manual pump jack/axle stand

Galvanised waste oil drum - Galvanised bucket - Eckrol motor oil can.

1'' sockets - Working

Stakes & chains not included

Marked as 26 - Wheels seized/corroded

Marked as 43 - Spares or repair - Untested - Dry stored

Steel pipe fittings

Marked 17 - 4 steps - C/w chequer plate top - This lot is part of a genuine dispersal, the vendor having relinquished his farm tenancy

Marked 18 - Approx 20' high reach - Good condition - This lot is part of a genuine dispersal, the vendor having relinquished his farm tenancy

Marked 22 - Approx 5'6'' at shortest - This lot is part of a genuine dispersal, the vendor having relinquished his farm tenancy

Semi Automatic compost stacking & palletising line - C/w all transfer & press belts - C/w pallet magazine - C/w motors (all 3 phase) - C/w operating control panel and electrics - May need some electrical attention as has not been used for approximately 5 years - Buyer to dismantle and remove.

3 phase electric motor - In good working order last time used

New and never used - For inverter welder